Posts Tagged ‘electrical installation’

electrical installation harmonic problems part 4

September 28th, 2009 | 2 Comments | Posted in Power quality
Tags: ,

Examples of harmonics-related malfunctions in electrical installations : case of  “High harmonic distortion loads”

High voltage distortion at Courchevel ski resort

High voltage distortion at Courchevel ski resort

(more…)

electrical installation harmonic problems part 3

September 21st, 2009 | Make a comment | Posted in Power quality
Tags: ,

Examples of harmonics-related malfunctions in electrical installations : case of  “Overloads on transformers or generators”

huge losts:  20,000 euros an hour   17 million euros

huge losts: 20,000 euros an hour ... 17 million euros ...

(more…)

electrical installation harmonic problems part 2

September 14th, 2009 | 4 Comments | Posted in Power quality
Tags: ,

Examples of harmonics-related malfunctions in electrical installations : case of  “Overloads in neutral conductors”

Paris headquaters Groupama discovered what Harmonics are !

Paris headquaters Groupama discovered what Harmonics are !

(more…)

Electrical Safety in Medium Voltage

September 7th, 2009 | 7 Comments | Posted in Electrical distribution, Safety
Tags: , , , ,

disconnector s in electrical installation s are not safety devices !

MV switch disconnector

MV switch disconnector

(more…)

electrical installation harmonic problems part 1

August 24th, 2009 | 5 Comments | Posted in Power quality
Tags: , ,

Examples of harmonics-related malfunctions in electrical installations : case of  “Overloads of correction capacitors”

Several capacitor banks had to be replaced prematurely in 2007
United Parcel Service, Louisville, Kentucky airport: several capacitor banks had to be replaced in 2007

(more…)

LV surge protection installation

July 20th, 2009 | 9 Comments | Posted in Electrical distribution
Tags: , , , ,

It’s Good to have in mind practical aspects: case of a low voltage  switchboard To achieve the effective installation of the , the surge arrester’s connections to the grid should be as short as possible. Any cable crossed by a impulse current has a significant voltage to be added to the Device (SPD) residual voltage.

nice picture from http://www.lafoudre.com/

nice picture from http://www.lafoudre.com/

(more…)

Power losses reduction in electrical distribution

June 29th, 2009 | 29 Comments | Posted in Electrical distribution, Electrical software
Tags: , ,

Reducing power losses by optimizing equipment locations

power-losses

 Do you realize that power losses in a electrical installation could represent up to 7 %  of the electrical consumption ?

LV cables and transformers are the most contributors to these operating losses, around 95 % as shown here below

 

 

 

(more…)

LV: Coordination between 2 Surge protection devices (SPD)

June 18th, 2009 | 10 Comments | Posted in Electrical distribution
Tags: , , , ,

& : Advice to ensure a  guaranteed protection  for a low voltage electrical installation

(more…)

New design software for electrical installation

June 1st, 2009 | 12 Comments | Posted in Electrical software
Tags: , ,

I have found a new on Internet: Simaris Design Basic. It is a software for electrical installation calculation: short-circuit calculations, cables sizing and protection devices choice and settings. This is a new version. I knew the old version of this software – 1.5, which is not available any more.

(more…)

Software for electrical installation

April 23rd, 2009 | 70 Comments | Posted in Electrical software
Tags: , , ,

I find the existing software for the calculation of difficult and long to use. Sometimes, I need to make a simple calculation or verification and I do not need to create a complete network to do it

Recently I have discovered some small calculators, some of them are too much simplified, but I find the idea good. There is for example… (more…)

Electrical engineering BLOG is proudly powered by WordPress
Entries (RSS) and Comments (RSS) and license Creative Commons License

webleads-tracker