How can fuses replace CBs in 3-phase systems? (back to basics)

megaphone-orange

As only few milliamperes can kill a human in a part of second, safety always is the big concern for electrical engineers and protection systems designing gets much more attention.

This is the topic our fellow electrical engineer Yasser chose to discuss today. As a reminder, you too can be published in this blog, just send a mail to the team!


Protection and fuses

Usually the word protection in electrical engineers’ glossary is associated with Circuit Breakers (CBs) and Fuses. These devices are the muscles of protection systems which isolate and protect them from different kinds of faults and/or abnormal conditions.

Over the years, many developments were done in both of them, the ratings became higher, many new environmentally friendly materials are used, and they became more accurate.

Each of CB and fuse has many advantages and disadvantages that mainly define which of them is the most suitable for the required application in our protection systems. There are many applications where CBs is the best choice and for others fuses are the most suitable.

In this article, we are going to discuss how today’s technology makes it applicable to use fuses instead of CBs to protect a multi-phase system which is no longer an advantage of CBs over fuses.


When to use a fuse?

As it is known, fuses are commonly used for low ratings because they are simpler and cheaper than CBs and they can protect the system from two kinds of fault, phase-to-neutral fault and phase-to-ground fault. However fuse is a single-pole protection device which means that it can only protect one phase from a multi-phase system.

Symbol for fuses

Fig.1 Symbol for fuses


This is no longer an obstacle as using a two or three fuses together to protect a multi-phase system is now applicable. The main challenge which was preventing having fuses working with multi-phase systems was the single phasing, it’s when one phase in the 3-ph motor opens and the remaining still in service coordination, in this case, the fuse of that phase will open only its phase, causing an over current, overheating and unbalance voltage at the other phases. Moreover sometimes this may cause damage to the equipment.

So, recently, a load break switch with striker is used as shown in figure 2. This mechanism ensures that when any of the fuses in any phase is blown up, a signal will be sent to a load break switch to open all the fuses and isolate the system.


Is it mandatory to replace all the fuses in each phase?

fuse switch disconnector symbol

Fig.2 Symbol for a fuse-switch disconnector + disconnector

*

Although this mechanism made it applicable to use fuses with multi-phase systems, it still has a problem. The problem is that in the case a fuse has blown up, all the three fuses will need to be replaced together.

Usually, in the case of system fault, a fuse in one phase is exposed to an over current which usually causes damage or partly interrupted of the fuse element and as a result, its current carrying capacity become lower and most probably won’t perform within its published performance characteristics in the event of another over-current.

So, take into consideration that re-using fuse elements, without replacing it, may make it melts at currents much below the minimum breaking current which will cause disastrous damage to the installation.


What should I use?

Fuses are a good choice when the maintenance is not periodically available, and the trip rate of the system determines where a fuse or a circuit breaker is the most suitable.

It’s obvious now that using fuses in a multi-phase is system is double-edged, it’s all about compromising you can now choose a lower cost fuses system in multi-phase, but also remember that you’ll have to change all the fuses even if the fault was only in one of them. It’s up to you.

Whatever your choice, please take care while replacing a fuse and make sure that all phases are isolated, because it may be very dangerous and your safety is a high priority.

2 Comments

  • In a motor circuit, the effect of one fuse opening on a phase to ground fault and the increase of current depends upon how the motor is protected and how the fuses are sized. If the fuses are sized at Code maximum, the increase in current will not affect the other fuses – because the overload relay if sized to the motor running current will take open since an overload is created in the other phases (173%). In this case, if one fuse opens, then you only need to replace two fuses. However, if the fuses are sized for back-up overload protection (125% or higher) then it may be needed to replace all three fuses. In motor circuits you can also take advantage of electronic trip overloads which can provide single phase and voltage unbalance protection – this is usually the best method to address this concern.

    Further in some applications single phase operation is of benefit. If you have a three phase panel supplying non-motor loads with a phase to ground fault, you only lose that phase when one fuse opens. The other phases remain operating.

Leave a Comment